PC Tsw 6 Enhancement | Lighting & Graphic Ep V6.1

If you expect that you better stop playing TSW... TSW will never be 100% constant 60fps.... Thats not possible due to how the game is build. You always noticed a small portion of loading/stutter

 

Tearing can appear on any FPS which differs from the screen refresh rate. If FPS drops below 60 or rise above it(on display with 60 Hz refresh mode), you'll likely get choppy frames. Enabling frame sync will help prevent this.
The author initially said that FPS drops below 60, under such conditions frame sync is needed(V-sync or freesync).

 

Where did you get the information from that he have a 60hz monitor?

 

I have never seen screens with a refresh rate below 60(except for old TVs). So it's just an example, insert any numbers and nothing will change.

 

Yeah but you need a higher fps amount then the amount of Hz that you monitor delivers to get tearing... In other ways its not possible so when you maximize your fps to 60 you never come above you're monitor Hz. It's not a magic program to get better FPS or more stable gameplay when you activate v-sync. Its only prevent tearing

 

Note also that if you run borderless full screen it goes through Windows DWM which adds its pseudo screen sync which often overrides other in game / control panel / monitor settings

 

If you have a 5090 why are you even using LS now?

Nvidia launched Smooth Motion last year for 40xx cards and above which does everything LS scaling did but built in on the card/firmware.
Just enable it forTSW in the Nvidia App.

 

My wife's laptop, when connected to a monitor, strictly limits the screen refresh rate to 50Hz at a resolution of 3440x1440. The monitor could be larger, but...

 

Seconded, Smooth Motion is superb. I've enabled it for TSW on my 4070 Ti Super, I've locked the game to 50fps so I'm getting a very nice 100fps for the most part.

 

This is old news I’m afraid, and something that’s been tested and adjusted a million times over. The mod is not to blame for default behaviour.

That command is in the Birmingham to Crewe preset, but it is set at 0.1. Any less than that causes insane shadow flickering at some of the stations, and I’ve seen that happen with it set as high as 0.09. It’s up to you what you set, I would prefer it to be set to 0.001 (as low as it can possibly go and as it is on most routes) but it makes the experience borderline unusable at a number stations, with New Street itself being the worst offender. In the latest version of the mod I’ve just removed the command entirely for that route and left it default

Obviously if you do as suggested and add that line then you will have a duplicate command which will cause issues of its own. If you wish to change it you need to edit the line in the requisite preset.

ps In the two pictures you are different distances from the AED, so of course the shadow will draw differently.

 

Ah thanks i have seen it now. Then i have missed that! And no i'm not blaming you're mod in anyway Is it possible that this line is added in the 6.1 version? And not before? Maybe i have missed a version...

 

It’s always been there but previously I used much lower numbers for it. I moved it to the main ini file and set it to 0.01 because I’d been seeing these flickering shadows on a number of routes (oddly it seems to be at it’s worst with any route with WCML in the title, but that is not exclusive). Having thought about it some more I believe it’s to do with light baking, because it always happens at stations that are baked (New street, Euston etc)

Anyway, on the routes where 0.01 causes this flickering I had increased the number until I no longer saw the problem occurring then added that to the ini for that specific route.

 

Ah okay thanks for the explanation.

 

No probs. It’s not ideal because it does improve things quite a lot but the flickering is definitely a problem. If my hypothesis is correct though about it being baking related perhaps there’s something can be done.

 

Should I expect a mod update with new routes? I'm definitely not rushing you.

 

This is like when a waiter drops the bill off at your table, whilst you’re still eating, and then says, “no rush”

 

It's not like the situation with Liberec Stara Paka Route, where the mod update unexpectedly came out quite quickly.

 

I've been playing around with Smooth Motion on my 4080, and, I kinda prefer Lossless Scaling?

I run in 4k and sometimes struggle to hit 60 fps unless I run on medium in-game settings.

With LS, I set fps in-game to 30, and then used LS to bring that up to 60. Of course I get the odd stutter, but it seemed very smooth all things considered.

With Smooth Motion I upped the frame rate in-game to 60 as 30 was just too low for a smooth experience, and I feel the little mini-stutters are much worse than with LS.

 

Doesn’t sound like you have it set up correctly then. Smooth motion does what Lossless Scaling does WRT to frame generation, but does it better.

 

Not sure how I can set it up incorrectly when I just turn it on for the TSW exe.

 

Which .exe mate, there are 2, 1 for the launcher and another for the actual game itself, make sure you point it towards the .exe in WindowsNoEditor/TS2Prototype/Binaries/Win64 otherwise it will not work.

 

It does sound like you haven't enabled it to the correct .exe file..... There are two and it could be you have enabled one but are using the other to actually run the game. As others have said you need to enable it for nthe .exe in the Win64 Binaries folder and then also ensure you are opening that same .exe when you start TSW.

To check you have correctly enabled SM for TSW do the following press "alt Z" and then select "Statistics" at the bottom.... Then select "View All".... Then enable FPS and Smooth Motion tick boxes along with anything else you want to see.

Then once in TSW press "alt R" and the HUD will display at the top right of the screen this will then show you the current fps and whether Smooth Motion (SM) is enabled or not.

 

Hello I don't know where I can download the mod ?

 

https://www.trainsimcommunity.com/m...6-lighting-visual-quality-enhancement-v-tsw61

Here you can found what you need. Read the manual before you start

 

JetWash
Can I ask you to make an .ini version for the Thames Valley addon? Johannes has made some weird changes to the night lighting, and the average .ini does not work for this addon.

The problem is that everything is extremely dark. Even the street lighting doesn’t shine far enough, which makes the whole scene look very dim. The clouds are also extremely dark at night.

If you could create a fix, it would be very welcome.

Thanks in advance!

 

Just as an aside, I find that setting fog to anywhere between 0.005 to 0.01 in God Mode does wonders for night driving; it adds just enough haze to lift the gloom.

 

What settings in the ini do i change to get the lighting of the track ahead a bit brighter?
Still seems way too dark for me

 

I’ve been using the one from GWE and it’s a decent improvement imo