Expansion Providence/stoughton Line Hsp46 - Feedback Thread

Weird isn’t it but you can change that in the settings. That bugged me too for the longest time.

 

I don't want to overrule anything. Especially since I'd like to use metric for those routes which use metric IRL. I like my UI using the same units as the incab screens and lineside signage.

 

Delivery To Providence...
After coupling the HSP46 to the coaches the loco no longer responds to the throttle or takes power.
As an experiment I uncoupled again and same thing, could not take power as light engine.
No switches in the cab have been changed by the player since running the loco light across the parallel track to the reverse point.

 

Put brake to suppression and release it, although that scenarios pretty broken

 

Thanks Bradley but as you say I noticed when I searched the forum, there were issues beyond the point where I got stuck.
Sounds like this was all a bit rushed through to release.

 

Yes sadly it does seem like that’s the case

 

Why is track speed limited to 80mph when atc/acses are letting me go a faster.

 

Depends of there is an older carriage in your train, those are limited to 80mph as far as I understand.

 

They bought this route back life maybe they should sort out the ACS-64 so cruise control works properly and no nasty wheel blur.

 

But how do you disable the cruisecontrol, it looks like that it only resets after a full stop.

 

I think you are supposed make sure its in neutral and throttle is idle then press soft key 2 . Thats then supposed to switch off but it doesn't switch off. But I could be wrong.

 

At my first try today, the Amtrak service got stuck on a red signal and didn' move (maybe a bug?). I'll try it again later.

 

I actually had no problems with this scenario. Thought it was well-designed. I'm quite impressed with the physics and performance of the HSP46.

The only issue was towards the end when you pass an Amtrak train on an adjacent track as you enter the Pawtucket sidings. Seems to be too close than it would be in real life. I thought I was going to collide with the other loco.

 

If you mean the HSP46, it's limited to 80 mph in service, even though designed for 110.

 

It does with with the cab cars and both engines track speed is slower then atc/acses speed.

 

Yes, that will happen with a diesel loco on the NEC.

 

Thanks for the info shame tho would be good to let them engines open up and hit the 100mph mark.

 

Are you on PC?

 

Yes.

 

F125 is also designed for 100 mph (some sources also list 125 mph), but during some testing I believe it showed quire shaky and not too stable at the higher speeds... but it is ok at the speeds it is used... however, also cos of this most others including Amtrak opted for Siemens Chargers instead... so the only customers atm are Metrolink (tho who knows, maybe in the future they manage to iron those bugs and their fortune changes)

P.S.: no idea how HSP46 performs at above 80 mph

 

It's worth pointing out that, for commuter railroads with frequent stops like the MBTA, Metra and Metrolink, top running speed is less important than the ability to accelerate faster out of station stops. Diesel electrics labor to get up to speed after a station stop. Engineers will start in higher notches to try to speed things up.

Electric traction is much more efficient, and there's some movement in that direction, though infrastructure costs are often prohibitive.

Commuter trains rarely get up to maximum speed, 50-60 mph or less is usually the cruising speed when in revenue service.

 

recently I started going notch 4-5 for slower diesels and 5-6 for HSP46 to get going and once they reach like 25-30 mph I go 7-8 ... not really based on engineers (they might go similar way I guess), but from my observations as a transpottter - watching trains set off from platform and seeing em reach like 30-50 kph as the end of a train leaves platform (I live in EU so it might be different but still)

 

Have just finished all the HSP46 scenarios, which are very well designed. I have to say that this loco and the control car are a joy to drive.

Even ATC and ACSES are behaving themselves.

 

mostly ... I am getting occasional PCS open right as I stop at the final station

 

Is there an update coming for this to sort out the little problems.

 

most likely yes but not before tsw6

 

Do these trains ever run longer formations. Its always one loco and five carriages.

 

Probably has to do with traffic needs. At over 4000 hp it's certainly capable of pulling longer trains.

Similar to Metra trains which are sometimes short in off peak but longer in rush hour, even double headed with 12+ cars.

 

wouldnt mind longer trains, at least I would get some practise in running more locos as MU

 

The fuse cabinet on the CTC-3 Cab Car doesn't have a trigger to open. I'm glad you don't have to pay extra for this if you have the MBTA Commuter DLC, honestly.

 

BS ain't you have to have the worcester route to use the locos from there so you can use the safetys

 

I have the MBTA Commuter DLC as well. So this is a bug.

 

None of the bugs are gonna get fixed on any route now until tsw6 is out . And then if the there is bugs with that the older routes will take longer for fixes. Thats what I think.

 

I am also experiencing the 23 hours 59 minutes issue on the Delivery For Providence Scenario on PS5. Can we expect to see a fix in TSW6? Thank you!

 

Has anyone done the road blocker scenario? If so was you able to switch on safety systems once in the cabcar. I can't open the cabinet to do so.

 

Epic Games just got a TSW6 update and so finally this little DLC loaded. Should i have had to wait this long for TSW6 to recognize DLC owned by the player ?