Issues I have found 1. The cab when selecting to drive the DB Br 110 displays Nicht Einsteigen rather than destination, this should be set up as 2 minutes to set up DB 110 and run back and forth and set the cab car destination isn’t enough time to do them tasks. 2. “Removed this issue due to confirmation it’s working as intended” 3. DB Br 101 train sets have passenger lights turned off. 4. Issue with PZB restricted mode (I’m aware this is noted) 5. Some Bushes enters the cab of the DB Br 110 just before heading over the bridge into Oldenburg 6. noticed some very strange textures on the DB Br 612 parked just before Oldenburg, it looked a bit like military camouflage 7. I’ve released the brakes on the cab car but the hud still shows red, is there something still on that I’ve missed ? Theirs quite some resistance to acceleration with it when this happens, there’s also a lot of Brake Hissing when this is occurring and the cab car is sort of rocking back and forth this rocking back and forth seems to happen quite a lot of the journey of the cab (especially when accelerating under about 70mph) I did fully release the cab car brake, when I reapplied it and released it again red hud went away but there was still rocking back and forth Hud remains red also sometimes after but can be turned back clear again if you move the reverser handle about (this has to be done nearly if not at every stop with the brakes) 8. Ai Cab car front end services (maybe both ways) don’t display correct PIS, it stayed as NichtEinsteigen, this may be because it’s heading eventually off World and that may not be an option on the scroll blind. Heading from Oldenburg to Bremen when i seen this Destination display light also off on some Ai cab cars (the ones where the cab car is at the back of set) 9. Some gang way doors only half animate opening, you can walk through them but on side they appear closed and you can appear to clip through, and on the other you can still see that the door handle is close but they are mostly visibly open they seem to be one of two doors, that are at where the carriages connect up gangways 10. When operating the Cab Car services the DB Br 110 does not activate automatically it’s TailLights 11. moving external camera not too far way from the PIS of the cab car, causes it to turn to a grey and blank until close enough (right up at it) to it again. 12. The DB Br 155 interior corridors where the PZB fuses are and internal engine is extremely bright and seems unrealistic compared to how the old Red DB Br 155 is dark in that corridor (in day or night) this may be missing some light baking or something… 13. Quite a lot of audio stuttering when applying a lot of brakes (the more you apply each time you pull the brake handle the more it stutters) noticed on the cab car 14. Not sure if this one is an issue or just different to other routes, the platform PIS at Bremen and what I noticed was a 425 to Nordenham displayed “RE” but no number, this is the same thing with RB services on The Platform PIS aswell. (time 10:05) 15. AI 425 service RE to Nordenham from Bremen HBf (leaves station at about 10:06.30) didn’t display headlights whilst boarding passengers, it did display them when it left the station 16. Possible Ai issue where a DB br 110 awaiting service at a little later time, didn’t display headlights or taillights but the intended rear of the train (cab car) does display taillights (At Bremen HBf 10:08) (awaiting service at 10:15) Xbox Series X
I want to add another issue I noticed in the DB BR 110. On the HUD, the brake-percentages of the automatic brake are not displayed correctly. When the automatic brake is in the release, running or off position, the braking is shown as 20% applied on the HUD, and automatic brake in the minimal position is shown as 30% and from then onwards each extra brake application is adding an extra 10% on the HUD The HUD in the cab-car shows the correct percentages. Playing Xbox One X
