If I need to do anything else, I just minimize the window that TSW is in and move on. This does not affect the game. Thought I must admit, I have...
The only way to safely pause the scenario you are running, if you have to do something, is the pause, which is esc button on PC. This does not...
The issue seems to be with the intermodal train which have their weight set way too low, 2653 tons on all of them, so it's very easy to control...
Guess you can't expect them to get all the train symbols correct, 294 is an intermodal.
The west bound tank trains are empty so the weight used is fairly close to a string of empty tankers. East bound, full trains, are 7893 tons.
I just went into HSC and SH to look at the weight of intermodal trains and found that Skyhook is using 2653 tons for all their IMs while in SH DTG...
For me it was always CRR, but now HSC is making an impression on me so think it will be right up there.
Just finished running 20Q, intermodal headed east which starts in Johnstown. Was a fun run and I was looking out for all the railfan landmarks....
I noticed that there does not seem to be the timing built into the sim for the dynamic setup. I can go right from power to dynamics, and they will...
In one of the threads, I seem to remember that this was brought up and shot down, since it would only work if it was a head end helper and most on...
That is correct, don't do anything to the other units.
Disintergration7, I found, after trial and error, that the setup is correct in the game. I played around with the trailing unit and DPU setting...
OK, somewhere in this thread people seemed to have forgotten that European trailers as you call them are the standard for international shipping,...
Just completed the first scenario in the Journey mode, grain train Altoona to Cresson JR Corman connection. Was a lot of fun once I trusted in the...
The one I have run had the rear brakes at a more realistic 78 lbs. Which is what it should be if the train had just come in from the east and...
Don't think any of them are at this point. Porta Rd. coming out of Altoona doesn't either and I have not looked at Carney's Crossing Rd yet. I had...
Those gons are used in the steel train which brings imported sheet from the docks to out near Pittsburg. Don't know if it is in the schedule or not.
Someone in the stream last week asked, "do the crossing gates work", simple answer NO. There are not very many level crossings on this route, PRR...
Well JD, the wait on Steam continues.
From what I have experienced, it has nothing to do with red lights. It seems to be the AI dispatcher again messing up paths. The first stuck train...
Have you run M3a service 2325? If not please do to see how it works for you. I have run a number of services without issues, so its not all...
M3A service 2325 GCT to Crestwood at 0735, empty stock move, is still broken. There is an inbound train stopped just north of the station with no...
OK, I was getting ready to re-run 2325, an M3a service, which has the same issue of an inbound M7a stuck north of Crestwood. It has passed the...
Remember as far as sounds inside the cab, these locomotives have the isolation cab so they would be low inside. Personal in the cabs of these and...
The GP9 at the curve has been corrected to face cab downhill as it should be.
From someone who has fanned the route from Cassandra east many times, I will be looking at that section of the line with close eyes. Hope to see...
I would like to add my congratulations to Natalie in her new role and, must say, will miss your pointed questions to Matt on behalf of the DTG...
Service 2325 GCT to Crestwood makes it almost to the end then encounters a red just over 900 yd short. I used the free roam camera to see what...
I just ran 502 without any issues. I will run some of the other noted later. [ATTACH]
That is correct.
I have not yet run any of these, so will do so later today and see what happens.
It is already available for pre-order in Steam at the usual 10% off.
This is what I am seeing on a run leaving Sursee at 23.30. Should note, I am using 4K. [ATTACH] [ATTACH]
Which services have caused this with you? So far, I have not encountered this issue in running Harlem. I would like to do some of the ones causing...
I seem to remember as I was running, that with ATCS, if it gets you for speed, that once you get below the required speed, it can be cleared...
I ran a test night run yesterday and, even with the room kinda bright, I could see fairly well. I think if I ran it after dark with most of the...
From my viewing of many Norwegian FLIRT cab ride videos, the single light above the cab will give a very bright light which is good out to the 400...
The first thing that comes to mind, and it may not be relevant, did you do a save before this?
Maybe so, but the 'l' key also turns it on if you are outside of the locomotive.
Noted the ETCS issue when coming up to yellow signals, tones you, then E brake comes on without giving the driver time to get down to 40 km/h,...
I have also been waiting, though right now I am having a lot of fun with Harlem and Luzern - Sursee. Will wait to see what it looks like since...
I just thought, if all the red signals at every station stop are gone, maybe ETCS level 2 might actually work without too much issue or at least...
The windshield does seem lighter, but what I am really happy about is, no more red signals at every station stop. Makes the run much smoother. I...
S1 is also the route number for Luzern to Sursee, per the SBB wensite.
The light function work with the 'L' key and if you are in the cab, turns on the cab light, and on the ground, the flashlight.
Been broke since day 1.
I was running a timetable scenario yesterday and noted a speed limit ahead of 165 km/h which went away very quickly. I think you are seeing that...
Thanks, I missed that line when looking. I am downloading it now.
In the intro to the ETCS they referred to a manual where additional details were found. I have searched in my files section without any luck....
Would be nice to try this route out, but it seems that Steam is running real late today. It is 13.30 here in the eastern US which makes it 10.30...
Separate names with a comma.
